LED Cabinet Lighting Installation Checklist
Question: What are your Power Requirements?
Are you installing A. 12V and 24V (low voltage lighting) or B. 120V (high voltage, hard-wired)?
A. 12V and 24V
Low voltage LED lighting is recommended and preferred for DIY.
LEDs are connected to a low voltage power supply, converting 120V into 12V and 24V, and keeping accidents to a minimum. Low voltage lighting also produces less heat, making for a more comfortable space
1. Do you have direct access to outlets or will you need to hard-wire?
2. How will you run your wire so that it is best concealed?
AdvantageS
Simple for DIY installations with no electrical wiring necessary
Electrical access is not required
Disadvantages
Wire and cords can be difficult to hide
Requires the use of electrical outlets
B. 120V
Please consult or hire an electrician if you are not certified to handle 120V wiring. High voltage wiring is not only dangerous, installation will void warranties if not properly installed.
AdvantageS
Best for concealing wires
Works best with wall dimmers
Electricians/installers are familiar with these systems
Disadvantages
Requires additional planning to route wires through cabinets
Requires direct access to 120V wiring
Not recommended for DIY
Recommended Tools Checklist For Low Voltage 12V and 24V Installations:
Cordless drill
Scissors or wire cutter
Wire stripper/cutter
2-wire 18AWG for standard lighting
4-wire 18AWG for RGB
5-wire 18AWG for RGBW
Materials needed for 12V and 24V LED Cabinet Light installations
LL50 24V LINKABLE LED LINEAR LIGHT
This bright, even illumination 24V Plug & Play system has simple installation with multiple ways to mount.
Just plug into a wall outlet and connect the linear bars together with in-line, wire, or corner connectors. Includes 2 x slim surface mount clips.
Determine if the following accessories are needed: G. Input Power, H. Touch Switch, I. Middle Connector, J. Corner Connector, K. Jump Connector, L. 45° Angle Clip
Wire: No wire required.
RD7 Recessed Puck Light
The RD7 1.75 inch Recess LED Cabinet Puck Light comes in 3 trim color finishes:
Black RD7 Trim, White RD7 Trim, Brushed Nickel RD7 Trim
You will need a tool capable of creating a 1-3/4 in. cut-out.
Installation is achieved by inserting the RD7 into the 1-3/4 in. cut-out. Pressure fit clips included on either side hold the puck firmly in place.
Wire: 18AWG 2-wire requirement.
RD7 Surface Mount or RecesS Puck Light
The RD7 1.75 inch Surface LED Cabinet Puck Light can also be a recessed trim-less LED Puck Light. Available in 3 trim color finishes:
Black RD7 Trim, White RD7 Trim, Brushed Nickel RD7 Trim
You will need a tool capable of creating a 1-3/4 in. cut-out if you wish to recess install.
Installation is achieved by mounting the included base using provided screws, or inserting the RD7 into a 1-3/4 in. cut-out. Pressure fit clips included on either side hold the puck firmly in place.
Wire: 18AWG 2-wire requirement.
RD10 4W Surface Mount Puck Light
The RD10 4W 2.25 in. Surface LED Cabinet Puck Light can also be a recessed LED Puck Light. Available in 3 trim color finishes:
Black RD10 Trim, White RD10 Trim, Brushed Nickel RD10 Trim
You will need a tool capable of creating a 2-1/4 in. cut-out if you wish to recess install.
Installation is achieved by mounting the included base using provided screws, or inserting the RD10 into a 2-1/4 in. cut-out. Pressure fit clips included on either side hold the puck firmly in place.
Wire: 18AWG 2-wire requirement.
RD24 GIMBAL RECESS LED SPOT LIGHT
1.75 inch recessed LED cabinet spot light
Available in 2 Trim colors:
White / Brushed Nickel.
You will need a tool capable of creating a 1-3/4 in. cut-out to install.
Installation is achieved by inserting the RD24 into a 1-3/4 in. cut-out.
Pressure fit clips included on either side hold the gimbal light firmly in place.
Wire: 18AWG 2-wire requirement.
RD12 MINI RECESS LED SPOT LIGHT
The RD12 is a super small 1-3/8 inch recessed LED cabinet light available in Black, White, and Brushed Nickel trims.
Very versatile, as it can be used as a plinth light or an upper cabinet light.
You will need a tool capable of creating a 1-3/8 in. cut-out to install.
Installation is achieved by inserting the RD12 engine into a 1-3/8 in. cut-out. Pressure fit clips included on either side hold the gimbal light firmly in place. Interchangeable trims screw onto the LED engine when in place.
Wire: 18AWG 2-wire requirement.
RGB (Colour Changing) LED PUCK LIGHT
2.25 inch RGB recess or surface mounted LED cabinet light allows you to choose any color using an RGB controller.
Black / White / Brushed Nickel trims available.
You will need a tool capable of creating a 2-1/4 in. cut-out if you wish to recess install.
Installation is achieved by mounting the included base using provided screws, or inserting the RGB RD10 into a 2-1/4 in. cut-out. Pressure fit clips included on either side hold the puck firmly in place.
Wire: 18AWG RGB 4-wire requirement.
1
Measure and Equip
Carefully plan and mark your LED lighting locations, paying specific attention to cut-out sizes, depths, and wire routing. Measure distances for space between lights, and determine whether you will be wiring to dimming switch plates, connecting power switches directly, or using wireless remotes.
2
Determine your LED Lighting requirements
What is the purpose of your lighting? Is it ambient or functional? Do you require flush mounted lights, or surface mounted?
3
Check Local Building Codes & Standards.
Be sure to check electrical code requirements and regulations for your region, and consult or hire an electrical contractor if unsure, or if hard-wiring is necessary.
4
PLAN LED Locations and Wire Routing.
Carefully plan and mark your LED lighting locations, paying specific attention to cut-out sizes, depths, and wire routing.
DIY Installation Requirements
Installation Materials Required
Selected LED Lights For Application: LL50 Linkable LED Light, RD7 LED Puck Light, RD10 LED Puck Light, RD12 Mini LED Spot Light, RD24 LED Gimbal Light, RD10 rgb LED Color Changing Puck Light.
Correct Wire and Lengths For Application: 18 AWG 2-wire for Standard applications, and/or 18AWG 4-wire for RGB Color Changing LEDs. Trace the line from the Power SOurce to the LED location using string to determine lengths required.
Wire stripper/cutter.
Wire Connectors and/or Marettes (Wire Nuts). Your LEDs should come with the connectors required to attached to the power Supply, however you may also need methods of connecting wire to wire.
Hole Cutting Tool: 2-1/4" Hole Saw for RD10 LED PUCK Lights, 1-3/8" for RD12 Mini LED Lights, and 1-3/4" for RD7 Puck Lights.
Correct Power Supply: 12V Low Voltage Power SupPlY (Driver) Required for RD10, RD24, RD12, and RD7. 24V Low Voltage Power SupPlY (Driver) Required for LL50. Choose whether you need your Low Voltage Drivers to plug into a standard outlet or if they will be hard-wired.
Corded or Cordless drill.
DIY Cabinet Lighting Installation
12V and 24V Low Voltage Lighting is relatively simple to install, and can be performed without accessing 120V wiring. Most applications can be done by connecting a Low Voltage Power Supply with a plug that will connect to any existing outlet. If hardwiring is required, seek out a professional electrician.
Warning:
Pay careful attention to the wire connections, especially if installing an in-line dimmer. The negative (-) and sometimes black wire must connect to the negative connector on a power supply (-) or wire on the LED. Do not let the wires touch each other. If the wires touch while connected to the Power Supply, you will risk possible and irreparable damage to the LEDs and/or Power Supply.